BIODIESEL & SVO DISCUSSION FORUMS





Sponsors    Biodiesel and SVO Forums Home    Forums  Hop To Forum Categories  Biodiesel  Hop To Forums  Biodiesel Equipment    Use of copper piping in biodiesel processors

Moderators: Shaun, The Trouts
Go
New
Find
Notify
Tools
Reply
  
Use of copper piping in biodiesel processors
 Login/Join
 
Member
posted
Hi All,
Please could the seasoned biodiesel producers comment on the use of copper piping in processors. I see that copper piping is used in the GL designs.What about galvanised water pipe as black piping is not available in my location. Copper piping is easier to work with and does a neat job.

Regards
Jock
 
Location: Kokstad.Kwazulu Natal.South Africa | Registered: June 23, 2012Reply With QuoteReport This Post
Member
posted Hide Post
copper is a bad idea. it degrades and causes stability issues with fuel. lose lose really.

i think the galvan coat can be stripped if its soaked in a certain solution. you could look into that.
 
Location: PEI, Canada | Registered: September 27, 2012Reply With QuoteReport This Post
member
posted Hide Post
quote:
Originally posted by andyman:
i think the galvan coat can be stripped if its soaked in a certain solution. you could look into that.


I soaked some galvanized fittings in straight white vinegar for about a week. Took nearly all of it off. Muriatic acid works too, but vinegar is cheaper.


Alvin
'01 F250 7.3 4x4 Lariat Crew
'95 Mercedes Benz E300 D
 
Location: Seattle | Registered: January 06, 2009Reply With QuoteReport This Post
Member
posted Hide Post
The English have been using lots of copper, they don't seem to be having problems, and they're very innovative. Does anyone have a link?
 
Location: New Zealand | Registered: August 15, 2006Reply With QuoteReport This Post
Member
posted Hide Post
I have used brass barrel nipples on all my tanks, including the processor, and they have done a good job for years now. Dunno if copper pipes are otherwise.


Land Cruiser 4.2tdi, Figo 1.4tdci,
W123 240d
 
Location: Bottom tip of Africa, Port Elizabeth | Registered: January 20, 2010Reply With QuoteReport This Post
Member
posted Hide Post
Wherever I've seen copper in contact with UVO there has been greasy, green corrosion and erosion of the copper. UVO also reacts with the zinc coating on galvanized pipe. Brass is relatively unaffected by UVO in most cases, which is perhaps odd since it's an alloy of copper and zinc.

If you can't get black iron pipe and fittings, then removing the galvanized coating with dilute acid is an option if you've got the time.

The plastic pipe/tube used in domestic hot water and hot water heating systems is another option which is inexpensive and easy to install.



 
Location: coldest N.America | Registered: May 03, 2005Reply With QuoteReport This Post



Member
posted Hide Post
i've seen the greenish residue in brass fittings as well. i suspect both copper and brass would hold up for years, but no point in using them if there are alternatives.
 
Location: PEI, Canada | Registered: September 27, 2012Reply With QuoteReport This Post
Member
posted Hide Post
Ive been using PVC pex pipe with brass compression fittings for 8 years with no problems. Its cheaper and easier than both steel or copper pipe. Beware of the various plastic fittings for plastic pipe, the seal in these fittings often use a rubber o ring which will only last a couple of weeks.
Copper, and to a lesser extent brass, will react with the biodiesel and will reduce the shelf life of the fuel but most brewers use their fuel as fast as they can make it so shelf life doesnt really matter.
 
Location: Lismore Ireland | Registered: November 25, 2007Reply With QuoteReport This Post
  Powered by Social Strata  
 

Sponsors    Biodiesel and SVO Forums Home    Forums  Hop To Forum Categories  Biodiesel  Hop To Forums  Biodiesel Equipment    Use of copper piping in biodiesel processors

© Maui Green Energy 2000 - 2014